JetCon 2401 Specifications
Overview
Specifications
Ordering Information
 Datasheet
Power Plant Automation |
Industrial Serial to Fiber Media Converter
- 3-in-1 RS232/422/485 to serial fiber media converter
- Easy DIP switch configuration to change serial modes without
resetting converter
- Supports Multi-mode 5KM, Single-mode 40KM
- PTP or SFR transmission mode for serial fiber ring communication
- Auto baud rate detection, selection and direction
- High level immunity with 15KV ESD protection
- Two-way 120 ohm line terminator embedded
- Dual modes for power input, AC 24V(12~32V)/ DC 24V(12~48V)
- -20~70oC operating temperature for hazardous environment
applications (JetCon 2401-mw/2401-sw: -40~70oC, special order by project request, please contact Korenix for lead time)
|
| Technology |
|
|
|
EIA/TIA-232 RS-232 (ITU-7 v.28)
EIA/TIA-422 RS-422 (ITU-T v.11)
EIA/TIA-485 RS-485 (ISO/IEC8284)
| |
|
|
|
RS-232 2-wires,RS-422 4-wire, RS-485 2/4-wire
| |
|
|
|
PTP mode: Peer To Peer wiring in Full or Half Duplex
SFR mode: Serial Fiber Ring in Half Duplex | |
| Interface |
|
|
|
1 x RS-232/RS-422/RS-485 serial port
1 x Fiber TX port , 1 x Fiber RX port | |
|
|
|
Serial port: 7-pin removable terminal block
Fiber port: Two ST connectors
Power input: 3-pin removable terminal block with earth ground | |
|
|
|
|
|
|
RS-232: 50 feet
RS-422: 4000 feet
RS-485: 4000 feet
Multi-mode fiber: 50/125um or 62.5/125um, max. distance 5KM
Single-mode fiber: 8/125um, 9/125um max. distance 40KM | |
|
|
|
RS-232: TxD, RxD, Signal Ground.
RS-422: TxD+, TxD-, RxD+, RxD-, Signal Ground
RS-485 4 wires: TxD+, TxD-, RxD+, RxD-, Signal Ground.
RS-485 2 wires: Data+, Data-, Signal Ground. | |
|
|
|
JetCon2401-m, Multi-mode:
Distance:5KM @ 62.5/125um multi mode cable with 3dbm/km attenuation
Wave-length: 820nm
TX Power: -12dBm (Min) ~ -9dBm (Max)
RX Sensitivity: -28dBm (Min)
Link budget: 16dBm
JetCon2401-s, Single-mode:
Distance: 40KM@9/125um single mode cable with 0.35dbm/km attenuation
Wave-length:1310nm
TX Power: -9dBm (Min) ~-8dBm (Max)
RX Sensitivity: -27dBm (Min)
Link budget: 18dBm | |
|
|
|
Switch 1 and 2: serial interface mode selection
Switch 3: RX 120ohm terminator Disable (off)/Enable (on)
Switch 4: TX 120ohm terminator Disable (off)/Enable (on)
Switch 5: PTP mode (off) / SFR mode (on). | |
|
|
|
Power LED: Power 1 (Green)
TX (Green): Serial port is on transmitting data.
RX (Yellow): Serial port is on receiving data.
Ring mode (Green): Working on SFR (Serial Fiber Ring) mode. | |
| Power Requirements |
|
|
|
Positive or negative power system.
DC 24V (12~48V) with reverse polarity protection.
AC 24V (AC12~32V, 50/60Hz)
Provides 0.65A over current protection | |
|
|
|
| Mechanical |
|
|
|
|
|
|
IP-31 protection, aluminum case | |
|
|
|
96mm (W) x 24.7mm(H) x 99mm (L) | |
|
|
|
0.24kg with package
0.135kg without package | |
| Environmental |
|
|
|
|
|
|
5% to 90% (Non-condensing) | |
|
|
|
|
|
|
| Regulatory Approvals |
|
|
|
FCC Class B; CE/EN55022:2003,class B; CE/EN61000-3-2:2001 Harmonic TestCE/EN61000-3-3:1995 Flicker test | |
|
|
|
EN61000-4-2:1998, ESD Testing, Level 3(Contact +/- 6KV, Air +/-8KV) with Criterion performance A), port to port (serial line, fiber port), port to power (serial to power, fiber to power)
EN61000-4-3:1998, RS testing, Level 3 (10V/m) with criterion performance A
EN61000-4-4:1995, EFT testing, Level 3 (Power supply:+/-2kV/5Khz; I/O:+/- 1Kv,5Khz), with criterion performance A
EN61000-4-5:1995, Surge test, Level 3 (L-N: +/- 2Kv), with criterion performance A
EN61000-4-6:1996, CS testing, Level 3 ,with criterion performance A | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
